Dress
up the plain factory front axle nuts with these beautiful CruiserFX chrome covers.
Choose from chrome plated billet aluminum "six shooter" or super-tough
ABS chrome covers.
Installation is
super easy! No special
tools are required. (Should take you about a minute.)
Just slip it over the fork nut, and tighten the set screw with the included
wrench
OK. This is what
the factory gave you.
This is what CruiserFX
is proud to offer.
Maltese Cross design -
Chrome ABS
Skull design - Chrome ABS
Six
shooter 44 MAG Billet Aluminum Axle Covers
Six
shooter 44 MAG Billet Aluminum Axle Covers
These
CNC machined, billet aluminum, chrome plated covers with the imbedded
.44 MAG
copper shells will transform your front end and are going to get you noticed!
Sold as
a set. (Because it is difficult to discern in the photo:
The 44
mag shells have the following embossed on them: "44MAG" and two stars connected
by a line.)
These covers are currently available in one type (size).
Measurements: 1 3/8" diameter by 1
3/8" long.
Chrome Plated ABS Axle Covers
Though
these covers are made from the more economical material
ABS,
the
high-quality finish of these super-tough covers will not disappoint you.
These covers are currently available in two
different types (sizes).
Installation is
super easy! No special
tools are required. (Should take you about a minute.)
These covers come in two different
types:
Type 1:
designed to fit Sportster (2003-2007), Softail, and some of the older
Dyna and Fatboy(the new ones use a larger axle diameter.)
If your specific model
and year was not mentioned above, please take special note of the following: It is
actually quite a challenge to list all the Harley models these covers will fit.
There have been many variations made from year to year of the components that
make up the front axle assembly. (for
example: The '07 Dyna has a larger round axle than some of the
older Dyna models.) So in
addition to the specific bikes mentioned above, several
of the Harley lines use similar engineering in the front axle assembly.
Therefore, we offer
the following photos and dimensions so you can more easily determine whether or
not these covers will fit both sides of your front axle.
Type 1 cover measurements: 1 1/4" diameter by 1" long.
If the Hex
nut on the left side measures 3/4" across (in other words, a 3/4" wrench fits
it, then the cover will fit.
If the round axle measures a hair under 7/8" diameter,
and
sticks off the fork no more than about 1 inch,
the
cover will fit fine.
Installation of Type 1 covers:
Just slip it over the hex nut (left side) or axle tube (right side) and tighten the set screw with the included
wrench. (Covers use stainless steel
self-locking set screws to securely hold them to the front axle.)
Type 2:
designed to fit Street Glide
and other models that use a larger axle diameter.
If your specific model
and year was not mentioned above, please take special note of the following: It is
actually quite a challenge to list all the Harley models these covers will fit.
There have been many variations made from year to year of the components that
make up the front axle assembly. (for
example: The '07 Dyna has a larger round axle than some of the
older Dyna models.) So in
addition to the specific bikes mentioned above, several
of the Harley lines use similar engineering in the front axle assembly.
Therefore, we offer
the following photos and dimensions so you can more easily determine whether or
not these covers will fit both sides of your front axle.
Type 2 cover measurements: 1 3/8" diameter by 1
3/8" long.
If the Hex
nut on the left side measures 3/4" across (in other words, a 3/4" wrench fits
it, then the cover will fit.
If the round axle measures 1 1/8" diameter,
and
sticks off the fork no more than about 3/4 inch, the
cover will fit fine.
Installation of Type 2 covers:
Just slip it over the hex nut (left side) or axle tube (right side).
Important FYI to prospective
buyers:
What if you purchase this
product and after seeing it in person you don't like it?
'Click'
here to
